Why One Area of Your Glass Furnace Wears Out First

Nov 20, 2026

Leave a message

Most of the lining may still appear serviceable, yet one sidewall section, corner or throat can force a difficult decision: continue monitoring, plan a repair, or bring the next shutdown forward. For a glass producer, local refractory wear is a production-planning problem, not just a brick-replacement cost.

 

info-800-560

Customers reviewing refractory blocks at Dezhong. Clear application information helps focus the technical discussion.
 

Before repeating the previous order or specifying a higher AZS grade, connect the wear location with the operating history and the original block specification. This article explains what to collect and how Dezhong can support the material and inspection review.

 

 

The aim is to identify the right questions before the next purchase. No photograph or single test can determine the remaining safe life of an operating furnace.

 

 

Use the wear location to guide the review

The position of damage is evidence, but it is not a diagnosis. Use the observations below to decide which records deserve attention. Several mechanisms can act together, and similar-looking damage can have different causes.

Observed pattern

Records to review before assigning a cause

Wear near the glass line

Glass-level history, the location of the worn band, local temperature records and changes in glass composition.

Lower-wall wear near electrodes

Electrode positions, boosting history, local temperature information and the location of the wear relative to the electrodes.

Wear concentrated at joints

As-built layout, joint and dimensional inspection records, working-face orientation and the condition of adjacent blocks.

Local loss after an operating upset

The event timeline, temperature changes, crack or spall observations, and dated photographs before and after the event.

Strong electrical boosting can change the thermal and corrosion profiles of a glass tank. Dezhong technical training materials also highlight the middle and lower regions of sidewall blocks in demanding applications. Looking only at the visible glass-line area can leave the review incomplete.

 

 

Technical reference :SEFPRO on AZS wear profiles and internal quality

 

Separate operating changes from material evidence

Start with a timeline. Did the wear pattern change after a glass-composition change, an increase in pull rate, an adjustment to electrical boosting or an operating interruption? A matching date is a useful lead, not proof of causation. Compare it with observations from unaffected areas where records are available.

info-800-560

Laboratory furnace operation shown in Dezhong company materials. Test conditions must accompany any reported result.

 

For the material review, retain the original grade, batch, casting type and inspection records. Dezhong has chemical-analysis and static and dynamic glass-corrosion testing capability. Discuss which checks and samples are relevant before commissioning a comparison.

 

 

A laboratory corrosion result needs the test glass, temperature, duration, method and units. It can support a comparison under defined conditions; it does not reproduce every condition in a working furnace or convert directly into years of service.

 

 

Technical reference:REFEL laboratory testing overview

 

Turn the findings into the next block specification

If the affected position has been identified, define its requirements on the drawing. Review the working face, casting type and internal-quality acceptance criteria as well as the chemical grade. An upgrade in zirconia content cannot by itself resolve a mismatch in these requirements.

info-800-560

Internal inspection of a refractory block at Dezhong before service. This is not in-service wall-thickness monitoring.

 

Dezhong radar inspection can support assessment of internal filling in supplied blocks. The inspection record should be linked to the block identity, orientation and agreed acceptance basis. A pre-service inspection of a new block is different from measuring residual thickness in a hot operating furnace.

 

 

When wear has followed a joint, carry the findings into dimensional checks, joint-face requirements and preassembly acceptance. Confirm the corrective scope with the furnace designer and the refractory supplier instead of changing only the grade on the purchase order.

 

 

Send a useful wear review enquiry

Describe the production concern

Tell us whether the concern is repeated wear at one position, an earlier-than-planned repair, or a changed wear pattern after an operating adjustment. Include the planned maintenance window. This helps separate an immediate site-safety decision from preparation for the next refractory order.

 

 

Provide a location and a timeline

Send a marked drawing, dated overview and close-up photographs, glass type, relevant operating records, and the original material and inspection documents. State which dimensions were measured, by what method and when. Label unavailable information as unknown rather than estimating it.

 

 

Agree what the review should deliver

Contact zzdz@dzrefactory.com to discuss material options, applicable tests and the next supply specification. A useful review identifies missing evidence and proposed checks before it recommends a change. It should not promise a fixed furnace-life extension without supporting service data.

 

 

Keep operating safety with the site team

Suspected leakage, rapid deterioration or abnormal hot spots require the site emergency procedure and qualified furnace personnel. Collect measurements or samples only under an approved safe inspection plan. Do not wait for a supplier email to decide whether continued operation is safe.

 

Send Inquiry